4.3

Out of 2 Ratings

Owner's of the ADC Clothes Dryer AD-170SE gave it a score of 4.3 out of 5. Here's how the scores stacked up:
  • Reliability

    4.0 out of 5
  • Durability

    4.5 out of 5
  • Maintenance

    4.5 out of 5
  • Performance

    4.5 out of 5
  • Ease of Use

    4.0 out of 5
of 58
 
18
NOTE: When the exhaust ductwork passes through a wall, ceiling, or roof made of combustible
materials, the opening must be 2-inches (5.08 cm) larger than the duct (all the way around).
The duct must be centered within this opening.
a. Outside Ductwork Protection
1) To protect the outside end of the horizontal ductwork from the weather, a 90° elbow bent downward
should be installed where the exhaust exits the building. If the ductwork travels vertically up
through the roof, it should be protected from the weather by using a 180° turn to point the opening
downward. In either case, allow at least twice the diameter of the duct between the duct opening
and the nearest obstruction.
IMPORTANT: DO NOT use screens, louvers, or caps on the outside opening of the exhaust
ductwork.
3. Multiple Dryer (Common) Venting
If it
is not feasible to provide separate exhaust ducts for each dryer, ducts from individual dryers may be
channeled into a “common main duct.” The individual ducts should enter the bottom or side of the main
duct at an angle not more than 45° in the direction of the flow and should be spaced at least 55-3/4”
(141.61 cm) apart. The main duct should be tapered, with the diameter increasing before each individual
18-inch (45.72 cm) duct is added.
IMPORTANT: The dryer is not provided with a back draft damper. When exhausted into a multiple
(common) exhaust line, a back draft damper must be installed at each dryer duct.
IMPORTANT: No more than three (3) dryers should be connected to one (1) main common duct.
The main duct may be any shape or cross-sectional area, so long as the minimum cross section area is
provided. The illustrations on page 20 show the minimum cross section area for multiple dryer round or
square venting. These figures must be increased 10 square inches (64.52 square centimeters) when
rectangular main ducting is used, and the ratio of duct width to depth should not be greater than 3-1/2 to
1. These figures must be increased in proportion if the main duct run to the last dryer to where it exhausts
to the outdoors is unusually long (over 20 feet [6.09 meters]) or has numerous elbows (more than two [2])
in it. In calculating ductwork size, the cross-sectional area of a square or rectangular duct must be
increased twenty percent (20%) for each additional 20 feet (6.09 meters). The diameter of a round
exhaust must be increased ten percent (10%) for each additional 20 feet (6.09 meters). Each 90° elbow
is equivalent to an additional 40 feet (12.19 meters) and each 45° elbow is equivalent to an additional 20
feet (6.09 meters).
IMPORTANT: For extended ductwork runs, the cross section area of the ductwork can only be
increased to an extent. Maximum proportional ductwork runs cannot exceed 20 feet
(6.09 meters) more than the original limitations of 20 feet (6.09 meters) with two (2)
elbows. When the ductwork approaches the maximum limits as noted in this manual,
a professional heating, ventilating, and air-conditioning (HVAC) firm should be
consulted for proper venting information.
IMPORTANT: Exhaust back pressure measured by a manometer in the exhaust duct must be no less
than 0 and must not exceed 0.3 inches (0.74 mb) of water column (W.C.).